PRO SIMRIG

PRO SIMRIG Slot-In cable clamps 10-packThese cable clamps have the advantage of sliding easily into the aluminum profile (they fit all PRO SIMRIG profiles and other Series 40 Slot 8 profiles). See photos of how they slide into the profile and then twist. Can be used in the vertical position as it fits snugly in the slot.The two-sided cable clamp can be opened and reused with different cables on each side.It has a rubber band inside to secure the cables and a clip on each arm to secure and keep them neat.No glue required.Made of durable black nylon 66 material.Color: BlackPrice is per pack of 10 clips

Read more less

PRO SIMRIG Monitor VESA Mounting Bolt and Spacer KitThis kit is suitable for PRO SIMRIG VESA mounts and most common monitor setups.It is becoming more common for monitors to have a deep recess where the standard monitor mount sits. This looks great and makes for a nice flush finish, but it does mean that it can be difficult to fit aftermarket VESA mounts.With this kit, you can screw through the PRO SIMRIG VESA mounts, overcome most notches with the 8mm spacer, and bolt it to the back of the monitor.Kit includes:4 x M4 16mm screw4 x M4 8mm brass spacers1 Set required per Vesa mount/monitor (i.e. if you have a triple monitor stand, order 3 sets).*Please note: While we have found this combination to work well for most monitors we have dealt with, not every monitor is the same and different screws and spacers may be required to attach your monitor to the VESA mount. If you need help with this, please contact us.

Read more less

PRO SIMRIG PSR3 blackNot all rigs are created equal. The thought process behind the PSR3 was "how do we squeeze this much stiffness out of a value-oriented cockpit without losing adjustability".The PSR3 is blessed with the same heavy-duty profiles used on the PSR1. Significantly thicker sidewalls provide more mass, more weight and more stiffness than the competition.On the steering knuckles, the steering area is overlapped. This requires more material and costs more, but the result is better anchoring of the steering wheel deck, which is supported by the rig perimeter.As with the PSR1, the wheelbase section is designed to be extremely strong. A 10mm thick aluminum wheel deck is used, connected to profiled and adjustable side plates.The PSR3 has a great pedal section. The design is an evolution of the PSR1, where two 10mm aluminum plates enclose two 80mm profiles mounted with 8 direct mounts. Many riders prefer a very stiff brake setup, and so the PSR3 had to be built with those requirements in mind. Other designs often suffer from flex in the pedal area, primarily due to cost savings in materials and design. BRACED SIDE MOUNT INCLUDED AS STANDARD In keeping with the motto "overlap = strength," the PSR3 features a braced side mount. This reduces lateral movement when shift levers or hand brakes are attached to the side mount. To help you find the perfect height, two different mounting heights allow for 80mm adjustment in 1mm increments. The side mount comes with 1 x 40x80x490mm profile and 1 x 40x40x350mm profile. The side mount can be attached to either the left or right side of the PSR3 cockpit. PSR3 comes standard with an externally braced side mount. PSR3 is designed for the new generation of Direct Drive wheelbases. Compatibility with many wheelbasesThe PSR3 wheel deck was built with mid-range direct drive wheelbases in mind (we consider wheelbases like the Fanatec CSL DD (with boost kit) and Simagic Alpha Mini to be "mid-range" direct drive wheelbases).They are extremely popular due to their mix of price, performance, and strength. The PSR3 was designed specifically for these vehicles.The PSR3 can also handle stronger direct drive motors like Fanatec DD1 and DD2, Simucube 2 and so on. Nevertheless, we recommend the PRO SIMRIG PSR1 if you are running these Wheelbaseswith high torque settings.The bold Wheelbases are recommended for the PSR3. The non-bold Wheelbases are recommended for the PSR1.Pre-drilled holes for floor mounting are available for the following Wheelbases: Fanatec CSL DD / DD Pro (with optional Boost Kit). Fanatec DD1 / DD2 Fanatec CSW Asetek La Prima / Asetek Forte / Asetek Invicta Simagic Alpha / Simagic Alpha Mini Moza R9 / Moza R16 / R21 All Thrustmaster / Logitech Simucube 2 (Sport / Pro) - requires Simucube 90 degree front mount - sold separately WIDE PEDAL COMPATIBILITYIt is common knowledge that the greatest consistency is achieved through the brake pedal. For this reason, the PSR3 is equipped with a pedal deck that offers wide compatibility with the best pedal systems.Compatible pedal systems that use the manufacturer's base plate: Fanatec CSL / CSL (+LC) / V1 / V2 / V3 (+inverted). Venym Atrax Heusinkveld Sim pedals Sprint / Ultimate / Ultimate+ Meca Cup1 / Evo1 BJ Steel Asetek Forte / Invicta Moza S-RP / CRP SimTrecs ProPedal GT SimCoaches P1 / SimCraft PRO / ImSim Talento Requires additional mounting hardware as these pedals mount from the bottom. Need 4 x corner brackets, 8 x T-nuts, 8 x bolts. Very easy to mount. Thrustmaster T-LCM / T3PA / T3PM Logitech (all) Fanatec CSR / CSR Elite Weight: 40kg (2 boxes)Easy to modify and add attachmentsProfile: PRO SIMRIG Ultra Heavy Duty 40x80 and 40x40Color: Black profile, black angle brackets, black angle bracket covers, black and silver screws

Read more less

PRO SIMRIG Slotcover 5mFlexible slot covers for aluminum profilesEasy to slide inAvailable colors: black white red blue yellow orange green 5m lengthSuitable for 40x40 Profinut 8For aesthetic purposes or to keep dust out of the ducts!Easy to cut with scissors or craft knife (be careful!)

Read more less

PRO SIMRIG Universal HolderThe Universal Holder is an inexpensive, versatile holder that can be used for a variety of things, including (but not limited to!): Button bar mount Headphone holder Steering wheel mount Webcam mount Bracket for key light Pre-drilled with M8 holes at both ends and 3 holes in the center for attaching attachments that need to be permanently mounted.Supplied as standard with 2 x M8 bolts, 2 x M8 washers and 2 x M8 slot nuts.Manufactured from 3mm thick carbon steel, powder coated in matt black.Dimensions: Inner length (distance between both ends) 130mm. Width (widest point) 80mm Width (narrowest point) 40mm Note: Profile, headphones and webcam are not included.

Read more less

PRO SIMRIG Integrated single monitor mount for PSR3 (650mm).Extra strong and rigid thanks to the 40x80 profile that solidifies the constructionStrong aluminum side platesMinor angle adjustments on the profile without having to move the side bracketsSupplied with a VESA 50/75/100 bracketBracket suitable for the PRO SIMRIG PSR3 or other aluminum extrusion where the outside of the uprights (or the inside of the uprights) is 650mm.Supplied with screws and T-nuts to attach to your rig.

Read more less

PRO SIMRIG Integrated single monitor mount for PSR1 (660mm)Extra strong and rigid thanks to the 40x80 profile that solidifies the constructionStrong aluminum side platesMinor angle adjustments on the profile without having to move the side bracketsSupplied with a VESA 50/75/100 bracketThe mount is suitable for the PRO SIMRIG PSR1 or any other aluminum profile rig where the outside of the uprights (or the inside of the uprights) is 660 mm.Supplied with screws and T-nuts to attach to your rig.

Read more less

PRO SIMRIG mouse pad with logoThe mouse pad fits PRO SIMRIG mouse tray 220x240mm with rubber pad

Read more less

PRO SIMRIG adjustable feet for monitor standIf you have an uneven floor, these adjustable feet can be added to level the monitor stand.A complete kit for mounting the feet to the monitor stand is included. The brackets are made of 10 mm thick black coated aluminum. The main bolts are M12 (12mm).The price is for a complete set of monitor stand feet. 4 feet, 4 brackets, screws, T-nuts and nuts.

Read more less

PRO SIMRIG heavy duty wheels set4 x 50mm red swivel castors + screw setNote: 2 wheels are lockable, 2 wheels are not lockable.Load capacity: 70kg per wheelHeight: 68mmWheel diameter: 50mmThese wheels offer an excellent aesthetic appearance. They are made of polyurethane, which offers excellent wear and abrasion resistance properties, high grip and resistance to many liquids and detergents, while having a high load capacity, as each caster wheel can support up to 70kg per wheel.Bolt set and T-nuts are included. Note that a Spherical head hex key may be required to obtain the proper angle to tighten the bolt from below.

Read more less

PRO SIMRIG side mountThe PRO SIMRIG side mount can be mounted on the side of your PRO SIMRIG PSR1 or other aluminum extrusion.The side mount provides the ability to add a manual shift lever or mouse pad tray, etc.A complete kit for mounting the side mount to the PSR1 rig is included.Compatibility:PRO SIMRIG PSR1Other 40mm profile rigs

Read more less

PRO SIMRIG PC StandPRO SIMRIG PC Stand for direct mounting on the PRO SIMRIG PSR1 Rig.Complete kit for mounting the PC stand on the PSR1 rig is included.A 22mm thick laminated board is included (66x25cm).The two main advantages of the PC stand are: Utilizing the space behind the monitors that you normally never use. Also, you can use shorter cables from the PC to the monitors, Wheelbase, etc.Compatibility:PRO SIMRIG PSR1Other 40mm profile rigs

Read more less