Accessories for Simrigs

PRO SIMRIG Slot-In cable clamps 10-packThese cable clamps have the advantage of sliding easily into the aluminum profile (they fit all PRO SIMRIG profiles and other Series 40 Slot 8 profiles). See photos of how they slide into the profile and then twist. Can be used in the vertical position as it fits snugly in the slot.The two-sided cable clamp can be opened and reused with different cables on each side.It has a rubber band inside to secure the cables and a clip on each arm to secure and keep them neat.No glue required.Made of durable black nylon 66 material.Color: BlackPrice is per pack of 10 clips

Read more less

Asetek SimSports® Front Mount Not only does the Front Mount look cool, but it also allows you to mount your Asetek SimSports® Direct Drive Wheelbase by attaching the front of the Wheelbase directly to the rig for a quick, sturdy and easy mounting option. This also allows for mounting on the inside or outside of the rig with easy adjustment options.The two holes on each side of the front mount allow you to attach on/off and torque off buttons for a sleek look to your sim rig. Designed specifically for the Asetek SimSports® Wheelbases, the Front Mount screws directly into the aluminum housing of the wheelbases. The 8mm thick, laser cut steel mount is a no compromise mounting solution.The mounting option on your rig also allows for a high degree of tilt, so you can adjust the angle of the Wheelbase to your preferred riding position. Adjusting the tilt angle is easily done with four screws, two on each side of the rig.

Read more less

PRO SIMRIG Slotcover 5mFlexible slot covers for aluminum profilesEasy to slide inAvailable colors: black white red blue yellow orange green 5m lengthSuitable for 40x40 Profinut 8For aesthetic purposes or to keep dust out of the ducts!Easy to cut with scissors or craft knife (be careful!)

Read more less

Steel bracket with lettering "O-Rouge

Read more less

PRO SIMRIG Keyboard Tray Fully adjustable keyboard tray.Complete kit for direct mounting on PSR1 or other aluminum extrusion rig (40 profile) is included.Keyboard tray is made of 4mm thick black coated aluminum.Compatibility: PRO SIMRIG PSR1 Other 40mm profile rigs

Read more less

The seat shifter can be used in combination with the seat holder. The width of the seat slider can be adjusted to the desired width by slightly bending the middle tie rod. This allows the seat slider to be made to fit all side-mounted bucket seats.Adjustment range of the slider: 23cm

Read more less

PRO SIMRIG mouse tray Mouse pad for mounting on the side mount of the PSR1 Rig.A complete kit for mounting the mousepad to the side mount is included. The tray is made of 4 mm thick aluminum and coated in black.Dimensions: 250 x 250 x 4 mmCompatibility: PRO SIMRIG PSR1 Suitable for mounting on other aluminum profile rigs.

Read more less

PRO SIMRIG Monitor VESA Mounting Bolt and Spacer KitThis kit is suitable for PRO SIMRIG VESA mounts and most common monitor setups.It is becoming more common for monitors to have a deep recess where the standard monitor mount sits. This looks great and makes for a nice flush finish, but it does mean that it can be difficult to fit aftermarket VESA mounts.With this kit, you can screw through the PRO SIMRIG VESA mounts, overcome most notches with the 8mm spacer, and bolt it to the back of the monitor.Kit includes:4 x M4 16mm screw4 x M4 8mm brass spacers1 Set required per Vesa mount/monitor (i.e. if you have a triple monitor stand, order 3 sets).*Please note: While we have found this combination to work well for most monitors we have dealt with, not every monitor is the same and different screws and spacers may be required to attach your monitor to the VESA mount. If you need help with this, please contact us.

Read more less

Asetek SimSports® Bottom Mount The Bottom Mount can be mounted directly to your table or rig. You mount your Asetek SimSports® Direct Drive Wheelbase by attaching the Bottom Mount to the bottom of the Wheelbase and then mounting it to your rig in the desired position.The T-slots on the bottom of the Wheelbase allow you to slide your Wheelbase back and forth on the mount. This mounting solution maximizes legroom in your setup and clears the way for comfortable and fully immersive sim racing. Dimensions: 460 x 120 x 5 mm Material: 5 mm laser cut steel Hole pattern: Wheel stand mount: 4-hole pattern (87 mm x 89 mm). Rig mount: 3-hole pattern, 4-hole pattern

Read more less

PRO SIMRIG heavy duty wheels set4 x 50mm red swivel castors + screw setNote: 2 wheels are lockable, 2 wheels are not lockable.Load capacity: 70kg per wheelHeight: 68mmWheel diameter: 50mmThese wheels offer an excellent aesthetic appearance. They are made of polyurethane, which offers excellent wear and abrasion resistance properties, high grip and resistance to many liquids and detergents, while having a high load capacity, as each caster wheel can support up to 70kg per wheel.Bolt set and T-nuts are included. Note that a Spherical head hex key may be required to obtain the proper angle to tighten the bolt from below.

Read more less

PRO SIMRIG side mountThe PRO SIMRIG side mount can be mounted on the side of your PRO SIMRIG PSR1 or other aluminum extrusion.The side mount provides the ability to add a manual shift lever or mouse pad tray, etc.A complete kit for mounting the side mount to the PSR1 rig is included.Compatibility:PRO SIMRIG PSR1Other 40mm profile rigs

Read more less

PRO SIMRIG adjustable feetIf your PSR1 rig is on a very uneven floor, you can add these adjustable feet to ensure that your PSR1 rig stands level.A complete kit for mounting the feet to the PRS1 rig (or any other rig) is included.The mounts are made of 15mm thick aluminum and are coated black.The screws are M16 (extra heavy duty).If your PSR1 rig is on a reasonably level floor, we recommend the PRO SIMRIG Premium Floor Mat. The floor mat compensates for minor floor unevenness and balances the rig itself, as it is made of 6 mm medium-hard foam.Compatibility:PRO SIMRIG PSR1Other 40mm profile rigs

Read more less