PRO SIMRIG

PRO SIMRIG Universal HolderThe Universal Holder is an inexpensive, versatile holder that can be used for a variety of things, including (but not limited to!): Button bar mount Headphone holder Steering wheel mount Webcam mount Bracket for key light Pre-drilled with M8 holes at both ends and 3 holes in the center for attaching attachments that need to be permanently mounted.Supplied as standard with 2 x M8 bolts, 2 x M8 washers and 2 x M8 slot nuts.Manufactured from 3mm thick carbon steel, powder coated in matt black.Dimensions: Inner length (distance between both ends) 130mm. Width (widest point) 80mm Width (narrowest point) 40mm Note: Profile, headphones and webcam are not included.

Read more less

PRO SIMRIG Integrated single monitor mount for PSR3 (650mm)Extra strong and rigid thanks to the 40x80 profile that solidifies the constructionStrong aluminum side platesMinor angle adjustments on the profile without having to move the side bracketsSupplied with a VESA 50/75/100 bracketBracket suitable for the PRO SIMRIG PSR3 or other aluminum extrusion where the outside of the uprights (or the inside of the uprights) is 650mm.Supplied with screws and T-nuts to attach to your rig.

Read more less

PRO SIMRIG PSR1 & PSR3 bottom mounted pedals mounting kit This kit is required for bottom-mounted pedals, e.g. for the Thrustmaster T-LCM. It is suitable for both the PRO SIMRIG PSR1 and the PRO SIMRIG PSR3.Contains: 4 x 40x40 Angle Brackets (Black) 4 x M8 T-slot nut 4 x M8x16 mm cap screw 4 x M6x16 mm button head screw 4 x M6x20 mm button head screw

Read more less

PRO SIMRIG M8 T-Slot Nuts (spring loaded) pack of 10 Type I, slot 8, M8 thread on the nuts. Suitable for 40x40 aluminum profiles.Suitable for all PRO SIMRIG aluminum profiles and profiles from other manufacturers that use the standard 40x40 I type profile (slot 8).These are spring-loaded roll-in slot nuts. This means that they can be “rolled” (pressed) into the upper part of the groove instead of having to insert them from the ends of the profile, which is not always possible.The spring-loaded ball bearing allows for easy placement while you tighten the screw.

Read more less

PRO SIMRIG mouse pad with logoThe mouse pad fits PRO SIMRIG mouse tray 220x240mm with rubber pad

Read more less

PRO SIMRIG PC StandPRO SIMRIG PC Stand for direct mounting on the PRO SIMRIG PSR1 Rig.Complete kit for mounting the PC stand on the PSR1 rig is included.A 22mm thick laminated board is included (66x25cm).The two main advantages of the PC stand are: Utilizing the space behind the monitors that you normally never use. Also, you can use shorter cables from the PC to the monitors, Wheelbase, etc.Compatibility:PRO SIMRIG PSR1Other 40mm profile rigs

Read more less

PRO SIMRIG PSR1 black with Wheelbase mount universalThe PSR1 is designed to give you maximum flexibility as you develop your driving skills and experience new styles and demands in racing simulation.You can start with a basic rig and purchase additional add-ons and accessories later.The highly customizable design of the PSR1 allows you to build the product to suit your individual needs.The PSR1 can be customized more or less in every way, both horizontally and vertically.The PSR1 rig consists of a base part, seat rails, a vertical part, a wheelbase part, the universal wheelbase posture and a pedal part with adjustable pedal plate.All parts such as brackets, screws, nuts, etc. are included.Various screws and nuts for mounting are included:Dimensions: Length: 1315mm Width: 660mm (outside of the wheel support brackets) Height: 820mm (top of the wheel holder supports) The PSR1 can be lowered with an additional upgrade kit.Supported Wheelbases: Logitech Driving Force wheels (G29, G920) Thrustmaster steering wheels (T300 etc.) Fanatec CSW (V2.5 etc.) Fanatec DD1 (mounted below) Fanatec DD2 (bottom mounted) Fanatec CSL DD (bottom mounted) Fanatec DD Pro (bottom mounted) SIMAGIC M10 (with SIMAGIC side mounts) Moza R9 / R16 / R21 (using Moza mounting plates - the 4-to-3 hole adapter) Other Wheelbases that mount from the bottom, or that come with 90-degree brackets that allow mounting from the bottom

Read more less

PRO SIMRIG Cable Management Tube 2mEasy to wrap around your cablesSimply open the rolled-up fabric to feed your cables through. The soft, flexible sleeve automatically rolls back and wraps around your cables. It can also be extended to wrap more cables if required. No tools are required and cables do not need to be disconnected from the computer to be inserted into the cable management sleeve.It is a soft textile sleeve, not the harder braided variety.Can be easily cut to any length: With a sharp pair of scissors, you can cut the cable guide sleeve to the desired length so that it fits exactly in and around your rig.Technical data: Length: 2m (6.5') Diameter: 32 mm (1.25") Flexible design Polyester and nylon Color: Black

Read more less

PRO SIMRIG Under TrayAn under tray for the side mount of the PSR1, PSR3 or any other aluminum profile rig. This is useful for storing your phone or other items without cluttering up your mouse compartment!A complete mounting kit for the Under Tray is included (3 x M6x16mm screws & 3 x M6x20mm screws & 3 x M6 T-nuts). You have two different screw lengths depending on whether you are mounting the PRO SIMRIG Mouse Tray or the PRO SIMRIG Mini Tray, or just the Under Tray alone.The tray is made of 4 mm thick aluminum and powder-coated in black.Dimensions (flat deck): 250 x 185 x 4 mmCompatibility: PRO SIMRIG PSR1 / PSR3 PRO SIMRIG mouse tray PRO SIMRIG mini tray Suitable for mounting on other aluminum profile rigs. Photos show other parts/accessories. This offer is only valid for the Under Tray.

Read more less

 PRO SIMRIG Adapter for Moza CPR2 and Simagic Haptic Reactor HPR Simply attached the Haptic Reactor to the bracket with the included screws. Then attach it to the pedal (either throttle or brake) using the additional supplied screw and locking nut.Price is for 1 bracket in black, plus M8 screw and locking nut.Note: this listing is only for the bracket and the bolt / nut to fix it to the pedal. It does not include any other product or item shown in the photos or video.Note: this product is a 3D printed part. It may have some small surface imperfections. This does not affect the function of the part. The design has been optimized and is printed to tight tolerances using high quality materials. This product will sustain normal UV exposure and normal room temperatures as well as normal PSU temperatures.

Read more less

 PRO SIMRIG Mini Tray A Mini Tray to add to the side mount of the PSR1, PSR3 or other aluminium profile rig.Complete kit for mounting the Mini Tray is included (2 x M6x16mm Bolts & 2 x M6 T-Slot Nuts).The tray is made of 4mm aluminium, powder-coated black.Dimension: 250 x 125 x 4 mmCompatibility: PRO SIMRIG PSR1 / PSR3 Suitable to mount to other aluminium profile rigs.

Read more less

PRO SIMRIG Integrated single monitor mount for PSR1 (660mm)Extra strong and rigid thanks to the 40x80 profile that solidifies the constructionStrong aluminum side platesMinor angle adjustments on the profile without having to move the side bracketsSupplied with a VESA 50/75/100 bracketThe mount is suitable for the PRO SIMRIG PSR1 or any other aluminum profile rig where the outside of the uprights (or the inside of the uprights) is 660 mm.Supplied with screws and T-nuts to attach to your rig.

Read more less